老松の枝の更新とは──葉のない古い枝を、ふところの若い枝で入れ替える庭師の手入れ(Renewing Old Pine Branches: How Japanese Gardeners Rejuvenate Aging Pines from the Inside)

老松 枝の更新 前と後 比較 枝が短くなる 葉が幹の近く 図解

何十年も手入れされてきた老松は、枝先ばかりが伸びて葉が先に集まり、幹に近いふところが裸になります。松は葉のない古い枝から芽を吹かないため、ふところに残る小さな若い枝を見つけて育て、数年かけて古い枝先と入れ替えます。その考え方と手順を図で示します。

日本の庭師・植木屋の剪定技術の連載です。秋から冬は松の手入れの季節で、これまでに古い葉をむしる「もみあげ」や、段をつくる「枝配り」を取り上げてきました。今回は、年を重ねた松の枝を若返らせる「枝の更新」の話です。後半に英語の全文を載せています。

 

老松の枝に起こること──枝先だけが伸び、ふところが空く

松の枝は、毎年、枝先の芽から1節ずつ伸びます。葉が付いているのは、枝先から2〜3年分の部分だけです。それより元の部分では、古い葉が落ちて、うろこ状の樹皮だけが残ります。

若い木なら、枝が伸びてもふところに光が届き、内側にも葉のある小枝が残ります。ところが長い年月がたつと、枝は少しずつ外へ外へと伸び、上の段の枝や枝先の茂みが重なって、内側が日陰になります。札幌市公園緑化協会の冊子は、松は日当たりが悪くなると芽を吹く力が弱くなるとしています。日の当たらないふところの小枝は弱って枯れ、枝は元が裸で、先だけに葉が付いた長い棒のようになります。

老松 枝 枝先だけに葉 ふところ 裸の枝 クロマツ 図解

年を重ねた松の枝。葉は枝先にだけ集まり、元の方は葉のない古い枝になる。幹の近くに小さな若い枝が1本だけ残っている(点線の円)

こうなった枝は、先が重くなって垂れ下がり、段の形が崩れます。枝先を切って小さくしたくても、切れる所が枝先の近くにしかありません。老松の手入れの難しさは、切る所が枝先にしか残っていないことにあります。

 

松は葉のない古い枝から芽を吹かない

枝の更新を考える前提は、松という木の性質です。サクラやケヤキは、太い枝を途中で切っても、樹皮の下に眠っていた芽が動き、切り口の近くから新しい枝が出ます。松はそうなりません。札幌の冊子は、松は不定枝を出さないので、切る時期と場所に十分注意するよう書いています。米国のペンシルベニア州立大学のエクステンションも、葉のない茶色の部分まで切り戻すと、その枝は芽を出さずに枯れるとしています。

松 剪定 切る位置 葉のある所 古い枝 枯れ込み 比較 図解

左は葉の付いた枝の分かれ目で切る正しい切り方。右は葉のない古い枝で切った例で、残った枝は芽を吹かずに枯れ込む

ですから、長く伸びた老松の枝を、葉のない所でばっさり短くすることはできません。切った先に葉が残っていなければ、その枝は枯れます。老松の枝を短くできるのは、その手前に葉の付いた若い枝が育っているときだけです。枝の更新とは、この「手前の若い枝」を、先に用意しておく手入れです。

 

ふところに残る小さな枝と芽を見つける

更新の手がかりは、ふところに残る、小さく弱々しい若い枝です。葉が数束しか付いていない短い枝や、古い枝の上にかろうじて残った芽が、これから育てる候補になります。

松 ふところ 若い枝 芽 古い枝 更新 手がかり 図解

古い枝の元に残る短い若い枝(大きい点線の円)と、小さな芽(小さい点線の円)。これが枝の更新の手がかりになる

職人の間では、こうした小枝は、普段の手入れで決して払わずに残すものとされています。見た目には貧弱で、整った段の中では邪魔にも見えます。けれども、10年先にその枝の役を継ぐのは、この小さな枝です。現場での経験から、老松の手入れでは、切る枝を探すより先に、残す小枝を探します。

見つけた小枝を育てるには、光と、木の力を内側へ回すことが要ります。松の手入れの基本の作業が、そのまま役に立ちます。

作業 時期の目安 更新での役目
もみあげ 10月ごろ 古い葉を取って、下の枝とふところまで日を当てる
みどり摘み 5月ごろ 枝先の強い芽を摘んで、勢いを内側の弱い芽へ回す
芽切り 春の芽を摘み、7月ごろの二番芽を育てる地方がある 短い芽を増やし、枝を密にする

出典: 日本造園組合連合会「造園初級技能の手引〔改訂新版〕」、長野県林業総合センター「ミニ技術情報 No.11 マツの剪定」

日本造園組合連合会の教材は、もみあげの目的を下の枝にも日を当てることとし、今年の枝先に30〜40本(15〜20対)の葉を残して、枝元と前年の枝の葉は取るとしています。長野県林業総合センターの資料は、みどり摘みで真ん中の強い1本を元から摘み、残りは3分の1ほど摘むとしています。枝先の勢いを抑えるほど、内側の弱い芽に力が回ります。

老松 枝の更新 1年目 枝先 強い枝 抑える ふところ 光 図解

更新の1年目。枝先の強い枝と頂芽を抑え(破線)、茂みを透かして、ふところの小さな枝(点線の円)まで光を入れる

 

数年かけて入れ替える──一度に切り戻さない

ふところの小枝に光が入ると、翌年から少しずつ葉の量が増え、枝が伸び始めます。職人の間では、この若い枝が、古い枝先の代わりを務められる太さと葉の量になるまで、数年待つとされています。その間も、古い枝先は切らずに残します。木の葉の量を急に減らさないためです。

老松 枝の更新 若い枝 育つ 数年後 ふところ 図解

2〜3年後。ふところの若い枝が伸び、葉の付いた小枝を広げ始めた(点線の円)。古い枝先はまだ残している

若い枝が育ったら、その分かれ目のすぐ先で、古い枝先を切り戻します。東京都の街路樹の仕様書も、太い枝を切るときは、後を継ぐ小枝のある所を見つけて、その先を切り取るとしています。札幌の冊子は、芽のない所で切る場合は葉を環状に残して切ると芽が出やすいとしています。切る位置は、必ず葉の付いた若い枝の分かれ目です。切り戻しの考え方は切り戻し剪定の回に書きました。

老松 枝の更新 切り戻し 切る位置 若い枝の分かれ目 図解

育った若い枝(点線の円)の分かれ目のすぐ先で、古い枝先を切り戻す(破線)。破線より先の点線の部分を外す

こうして枝を入れ替えると、枝は短くなり、葉の付いた所が幹の近くに戻ってきます。

老松 枝の更新 前と後 比較 枝が短くなる 葉が幹の近く 図解

左は更新の前。右は数年かけて更新した後で、枝が短くなり、育てた若い枝(点線の円)が新しい枝先になった

一度に何本もの枝を入れ替えないことも大事です。国際アーボリカルチャー協会(ISA)の一般向けの資料は、一度に取り除くのは樹冠の25%までとし、成熟した木ではそれより少なくするよう勧めています。老松では、1年に入れ替える枝を数本にとどめ、木全体を何年もかけて少しずつ若返らせます。段ごと古くなった枝は、すぐ上や下に育てた若い枝に段の役を譲らせてから外します。

仕立て松 段 古い枝 若い枝 役を譲る 更新 図解

古くなって長く垂れた段の枝(点線)は、すぐ上に育てた若い枝(点線の円)が段の役を継げるようになってから、付け根の少し外で外す(破線)

 

弱った老松は、切る前に根と土を見る

枝の更新は、木に芽を吹く力が残っていてこそできる手入れです。長野の資料は、木の勢いが衰えているときは、その年に限ってみどりを摘むのを控えるよう書いています。葉を減らす手入れは、弱った木をさらに弱らせるからです。

国土技術政策総合研究所の巨樹・老樹の事例集には、舗装に囲まれて勢いの落ちた樹齢約400年のクロマツが、植えられた場所を広げて土を改良したことで、生育が良くなった例が載っています。老松の勢いが落ちているときは、枝を切る前に、根の張る土と、根元の踏み固めを先に見ます。葉の色、今年伸びた枝の長さ、ふところの芽の数は、樹勢を読む手がかりになります。

長く伸びた枝をすぐに短くできないあいだは、支柱で下から支えて、枝が裂けるのを防ぎます。現場での経験から、枝と支柱が当たる所には杉皮などの当て物をして、樹皮を傷めないようにします。年を重ねた松の支柱の例は、江戸川区の臥竜の松の支柱の記事に書きました。

老松 支柱 枝支柱 長い枝 当て物 杉皮 縄 図解

長く重くなった下の段の枝を、丸太の支柱で下から支える。枝と支柱の当たる所には当て物をして縄でくくる(点線の円)

切り口に塗る保護剤については、ISA の資料は腐朽を減らす効果は認められないとし、国内の街路樹の基準には太い切り口に癒合剤を塗る決まりがあります。考え方は枝の付け根で切るの回にまとめました。

 

職人の目と手──10年先の枝を残す

老松の枝の更新は、1回の手入れでは終わりません。今年残した小さな枝が、古い枝の代わりになるのは数年先です。職人は、木の前に立つと、今の姿と同時に、数年後の枝の形を思い描きながら手を動かします。

庭師 植木屋 老松 ふところ 芽 手で確かめる 三脚脚立 イラスト

三脚脚立に乗り、ふところの小さな若い枝の芽を指先で確かめる職人(点線の円)

ふところの小枝は、外から眺めているだけでは見えません。職人は脚立に上がり、枝の内側に顔を入れ、指先で芽をなでて、生きているか、どちらを向いているかを確かめます。現場での経験から、芽の張りや、残っている葉の色つやは、手で触れてはじめて分かることが多いものです。どの小枝を残し、どの枝先を何年後に外すか。その判断は、毎年同じ木に通う中で少しずつ固まっていきます。

庭の松が何代もの職人に受け継がれてきたのは、ひとりの職人の手入れが、次の世代の枝をつくる仕事でもあったからです。今日切らずに残した小さな枝が、10年後の段になります。急がずに枝を入れ替えていく手間こそ、老松を老松のまま美しく保つ技術です。海外のアーボリストの間には、老木の樹冠を何十年もかけて少しずつ下げる「リトレンチメント剪定」という考え方があります。枝の途中から芽を吹く広葉樹のための方法ですが、時間をかけて木を若返らせるという点で、日本の老松の手入れと通じるところがあります。

 

よくある質問(Q&A)

Q1. 老松の長く伸びた枝を、途中で切って短くできますか?

A. 葉のない所では切れません。松は葉も芽もない古い枝から芽を吹かないため、葉のない所で切ると、その枝は枯れます。短くできるのは、手前に葉の付いた若い枝があるときだけで、その分かれ目のすぐ先で切り戻します。

Q2. 松の枝の更新とは何ですか?

A. 年を重ねて長く伸び、ふところが裸になった枝を、内側に残る若い枝と入れ替えて若返らせる手入れです。ふところの小枝に光を入れて育て、十分に育ってから古い枝先を切り戻します。

Q3. 更新にはどのくらいの年数がかかりますか?

A. 1本の枝で数年、木全体ではさらに長くかかります。若い枝が古い枝先の代わりを務められるまで育つのを待ち、1年に入れ替える枝も数本にとどめるためです。

Q4. 弱っている老松も、枝の更新をしてよいですか?

A. 先に樹勢の回復を考えます。葉を減らす手入れは弱った木をさらに弱らせるので、勢いが衰えているときはみどり摘みも控えます。根の張る土や根元の踏み固めを見て、土の改良などを先に行います。

Q5. 老松の長い枝が垂れてきたら、どうすればよいですか?

A. すぐに短くできない枝は、支柱で下から支えて裂けるのを防ぎます。枝と支柱の当たる所には当て物をして、樹皮を傷めないようにします。そのうえで、ふところの若い枝を育てて、数年かけて枝を入れ替えていきます。

 

マンション・施設・行政のご担当者様へ
当社は、年間の植栽管理、樹木診断、樹木の剪定・伐採のご相談を承っています。管理の進め方や診断の流れは、資料ダウンロードのページでご覧いただけます。ご相談はお問い合わせフォームからお待ちしています。

 

出典・参考情報

・財団法人札幌市公園緑化協会『すくすくみどり No.21 元気な庭木を育てる ―整枝・剪定方法―』p.10(マツは不定枝を出さない、葉を環状に残して切る、日当たりと萌芽力、もみあげ)
・一般社団法人日本造園組合連合会「造園初級技能の手引〔改訂新版〕」平成27年3月(切り戻し、もみあげで残す葉の量、芽切りと土用芽)
・長野県林業総合センター「ミニ技術情報 No.11 マツの剪定」平成11年5月(みどり摘み、樹勢が衰えたときは摘むのを控える)
・東京都建設局『街路樹等維持標準仕様書 緑地管理編』平成25年4月 p.8(後継枝となる小枝を見つけてその先を切る)
・国土技術政策総合研究所「巨樹・老樹の保全対策事例集」国総研資料 No.566、2010年1月(マツ類の土壌改良の事例)
・東京都建設局『令和三年度 街路樹診断等マニュアル』p.75(切り口の癒合剤)
・International Society of Arboriculture「Pruning Mature Trees」2021年(一度に取り除く量、切り口の塗布剤)
・Penn State Extension「Pruning Needled Evergreens」2024年1月
・University of Wisconsin–Madison Extension「Pruning Evergreens」
・Arboricultural Association, Reg Harris「Thoughts about retrenchment pruning」2018年(リトレンチメント剪定)

 

関連記事

・松の「もみあげ」とは──古い葉を手でむしる冬の手入れ
・松の枝配りとは──段をつくり、枝を水平に保つ庭師の手入れ
・クロマツとアカマツの違い──見分け方と、庭師が変える手入れ
・仕立て松の手入れ
・松の伝統技術「短葉仕立て」とは
・切り戻し剪定とは──芽の上と分かれ目で切る
・枝の付け根で切る
・剪定の時期──落葉樹と常緑樹、針葉樹
・寿昌院 臥竜の松 池の中の支柱を保存樹の仕様に
・200年の時を超える「臥竜の松」 古地図と地名が語る土地の記憶
・庭園樹のアカマツ 樹木医による樹勢回復

株式会社トシ・ランドスケープ
樹木医 中村雅俊

 

Renewing Old Pine Branches: How Japanese Gardeners Rejuvenate Aging Pines from the Inside

On an old pine that has been tended for decades, the branches keep extending at the tips, the needles gather at the ends, and the interior near the trunk (futokoro) goes bare. Because pines do not resprout from old wood without needles, gardeners find the small young shoots that survive in the interior, grow them on, and over several years exchange them for the old branch ends. This article illustrates the idea and the procedure.

This article is part of our series on the pruning techniques of Japanese gardeners (niwashi, ueki-ya). Autumn and winter are the season for pine care, and we have already covered momiage, the plucking of old needles, and edakubari, shaping branches into tiers. This time the subject is eda no kōshin, the renewal of branches on an aging pine.

What happens to the branches of an old pine: growth at the tips, a bare interior

Each year a pine branch extends by one segment from the bud at its tip. Needles remain only on the last two or three years’ growth. Further back, the old needles fall and only scaly bark is left.

On a young tree, light still reaches the interior as the branches grow, and small shoots with needles survive inside. Over many years, however, the branches creep steadily outward, and the tiers above and the foliage at the tips overlap and shade the interior. The Sapporo Park and Greenery Association notes that pines lose vigor in their buds when they are poorly lit. Shaded interior shoots weaken and die, and the branch becomes a long pole, bare at the base and leafy only at the tip.

老松 枝 枝先だけに葉 ふところ 裸の枝 クロマツ 図解

A branch on an aging pine. Needles gather only at the tip and the base is old wood without needles. A single small young shoot survives near the trunk (dotted circle).

Such a branch grows heavy at the end and droops, and the tier loses its shape. Even if you want to shorten it, the only places you can cut are near the tip. The difficulty with an old pine is that the places where you can cut survive only at the branch ends.

Pines do not resprout from old wood without needles

The starting point is the nature of the pine itself. Cherry or zelkova will push new shoots from dormant buds under the bark near a cut, even when a thick branch is shortened partway along. Pines will not. The Sapporo booklet warns that pines do not produce adventitious shoots, so the timing and position of cuts need great care. Penn State Extension likewise states that cutting back to brown wood without needles will not encourage growth, and the branch will die.

松 剪定 切る位置 葉のある所 古い枝 枯れ込み 比較 図解

Left, the correct cut at the fork of a branch carrying needles. Right, a cut on old wood without needles; the remaining stub does not resprout and dies back.

So a long branch on an old pine cannot simply be cut short where there are no needles. If no needles remain beyond the cut, the branch dies. You can shorten an old pine branch only when a young branch with needles is already growing behind the cut. Branch renewal is the work of preparing that young branch in advance.

Finding the small shoots and buds left in the interior

The key to renewal is the small, weak young shoot surviving in the interior: a short shoot with only a few bundles of needles, or a bud barely hanging on to the old wood. These are the candidates to grow on.

松 ふところ 若い枝 芽 古い枝 更新 手がかり 図解

A short young shoot at the base of an old branch (large dotted circle) and a small bud (small dotted circle). These are the starting points for branch renewal.

Among craftsmen, such shoots are something you never clear away in routine work. They look poor and even out of place within a neat tier. Yet it is this small shoot that will take over the branch’s role ten years from now. In our field experience, when tending an old pine we look for the shoots to keep before we look for the branches to cut.

To grow the shoot on, it needs light, and the tree’s strength needs to be redirected inward. The basic operations of pine care serve this purpose directly.

Operation Approximate timing Role in renewal
Momiage (plucking old needles) Around October Remove old needles so light reaches the lower branches and the interior
Midori-tsumi (candle pinching) Around May Pinch the strong candles at the tips to shift vigor to the weaker inner buds
Mekiri (bud cutting) Some regions remove the spring buds and grow on the second flush around July Increase short shoots and densify the branch

Sources: Japan Federation of Landscape Contractors, Guide to Basic Landscaping Skills; Nagano Prefectural Forestry Research Center, Mini Technical Note No. 11

The Japan Federation of Landscape Contractors describes the aim of momiage as letting sunlight reach the lower branches, leaving 30–40 needles (15–20 pairs) on this year’s shoot tips and removing the needles at the branch base and on last year’s growth. The Nagano Prefectural Forestry Research Center describes pinching out the strong central candle at its base and reducing the rest by about one third. The more the vigor at the tip is held back, the more strength reaches the weak inner buds.

老松 枝の更新 1年目 枝先 強い枝 抑える ふところ 光 図解

Year one of renewal. The strong shoots and terminal bud at the tip are held back (dashed lines), and the foliage is thinned so light reaches the small interior shoot (dotted circle).

Exchanging over several years, never cutting back all at once

Once light reaches the interior shoot, it gradually gains needles and begins to extend from the following year. Among craftsmen, one waits several years for the young branch to gain the thickness and foliage to take the place of the old branch end. Meanwhile the old end is left uncut, so as not to reduce the tree’s foliage suddenly.

老松 枝の更新 若い枝 育つ 数年後 ふところ 図解

Two or three years later. The young interior branch has extended and begun to spread shoots with needles (dotted circle). The old branch end is still kept.

When the young branch has grown, the old end is cut back just beyond its fork. Tokyo Metropolitan Government’s street tree specification likewise directs that, when cutting a large branch, you find the place where a small successor branch grows and remove the part beyond it. The Sapporo booklet adds that when cutting where there are no buds, leaving a ring of needles makes new buds more likely. The cut is always made at the fork of a young branch carrying needles. The idea of reduction cuts is covered in our article on kirimodoshi.

老松 枝の更新 切り戻し 切る位置 若い枝の分かれ目 図解

The old branch end is cut back just beyond the fork of the grown young branch (dotted circle; dashed line). The dotted part beyond the dashed line is removed.

Exchanged in this way, the branch becomes shorter and the needle-bearing part returns close to the trunk.

老松 枝の更新 前と後 比較 枝が短くなる 葉が幹の近く 図解

Left, before renewal. Right, after renewal over several years: the branch is shorter and the young branch that was grown on (dotted circle) has become the new branch end.

It is also important not to exchange many branches at once. The International Society of Arboriculture advises removing no more than 25% of the crown at one time, and less on mature trees. On an old pine we limit renewal to a few branches a year and rejuvenate the whole tree little by little over many years. Where an entire tier has grown old, its branch is removed only after a young branch grown just above or below can take over the tier’s role.

仕立て松 段 古い枝 若い枝 役を譲る 更新 図解

An old tier branch that has grown long and drooping (dotted) is removed just outside its base (dashed line) only after the young branch grown just above it (dotted circle) can take over as the tier.

For a weakened old pine, look at the roots and soil before cutting

Branch renewal depends on the tree still having the strength to push buds. The Nagano note advises refraining from candle pinching for that year when the tree’s vigor has declined, because reducing foliage weakens a weak tree further.

A case collection on giant and old trees by Japan’s National Institute for Land and Infrastructure Management describes a Japanese black pine of about 400 years, weakened by surrounding pavement, whose growth improved after its planting area was widened and the soil improved. When an old pine is losing vigor, look first at the soil where its roots grow and at compaction around the base before cutting any branches. Needle color, the length of this year’s shoots and the number of interior buds are clues to its vigor.

While a long branch cannot yet be shortened, a prop from below keeps it from splitting. In our field experience, padding such as cedar bark is placed where branch and prop meet to protect the bark. An example of props for an aged pine appears in our article on the Garyū pine in Edogawa.

老松 支柱 枝支柱 長い枝 当て物 杉皮 縄 図解

A long, heavy lower-tier branch supported from below by log props, padded and tied with rope where branch and prop meet (dotted circle).

On wound dressings, the ISA states that they do not reduce decay, while some Japanese street-tree standards require a dressing on large cuts. The arguments are summarized in our article on cutting at the branch collar.

The craftsman’s eye and hand: leaving the branch of ten years from now

Renewing the branches of an old pine is never finished in one visit. The small shoot kept this year will replace an old branch only years later. Standing before the tree, a craftsman works while picturing both its present form and the shape of its branches several years ahead.

庭師 植木屋 老松 ふところ 芽 手で確かめる 三脚脚立 イラスト

A craftsman on a tripod ladder feeling the bud of a small young interior shoot with a fingertip (dotted circle).

Interior shoots cannot be seen by looking from outside. The craftsman climbs the ladder, puts their head inside the branch, and strokes the buds with a fingertip to feel whether they are alive and which way they face. In our field experience, the firmness of a bud and the sheen of the remaining needles are often things you learn only by touch. Which shoots to keep, which branch ends to remove and in how many years: those judgments settle little by little over years of returning to the same tree.

Garden pines have been handed down through generations of craftsmen because each craftsman’s work was also the making of the next generation’s branches. The small shoot left uncut today becomes a tier ten years from now. The unhurried work of exchanging branches is the skill that keeps an old pine beautiful as an old pine. Among arborists abroad there is the idea of retrenchment pruning, lowering the crown of a veteran tree gradually over decades. It is a method for broadleaved trees that resprout along their branches, but in rejuvenating a tree by taking time, it has something in common with the care of old pines in Japan.

Frequently asked questions

Q1. Can a long branch on an old pine be cut partway to shorten it?

A. Not where there are no needles. Pines do not resprout from old wood without needles or buds, so a cut there kills the branch. It can be shortened only when a young branch with needles grows behind the cut, cutting just beyond that fork.

Q2. What is branch renewal on a pine?

A. It is the work of rejuvenating a branch that has grown long with age and gone bare in the interior, by exchanging it for a young branch surviving inside. The interior shoot is given light and grown on, and the old branch end is cut back once the shoot is well grown.

Q3. How many years does renewal take?

A. Several years for one branch, and longer for the whole tree, because you wait for the young branch to grow enough to take over the old branch end and exchange only a few branches each year.

Q4. Can branch renewal be done on a weakened old pine?

A. Consider restoring its vigor first. Reducing foliage weakens a weak tree further, so even candle pinching is held back while vigor is low. Look at the soil where the roots grow and compaction around the base, and improve the soil first.

Q5. What should be done when a long branch on an old pine starts to droop?

A. A branch that cannot be shortened right away is supported from below with a prop to keep it from splitting, with padding where branch and prop meet to protect the bark. Then the young interior branch is grown on and the branch is exchanged over several years.

Sources

– Sapporo Park and Greenery Association. Sukusuku Midori No. 21: Growing healthy garden trees — training and pruning, p. 10.
– Japan Federation of Landscape Contractors. Zoen shokyu gino no tebiki (Guide to basic landscaping skills), revised edition. March 2015.
– Nagano Prefectural Forestry Research Center. Mini Technical Note No. 11, “Pruning Pines”. May 1999.
– Tokyo Metropolitan Government Bureau of Construction. Street tree maintenance standard specification, green space management. April 2013, p. 8.
– National Institute for Land and Infrastructure Management. Conservation case studies of giant and old trees. NILIM Report No. 566, January 2010.
– Tokyo Metropolitan Government Bureau of Construction. Street tree diagnosis manual, FY2021, p. 75.
– International Society of Arboriculture. Pruning Mature Trees. 2021.
– Penn State Extension. Pruning Needled Evergreens. January 2024.
– University of Wisconsin–Madison Extension. Pruning Evergreens.
– Arboricultural Association, Reg Harris. Thoughts about retrenchment pruning. 2018.

Masatoshi Nakamura
Jumokui (Tree Doctor), Toshi Landscape Co., Ltd., Tokyo

人気の記事
最新の記事
おすすめ記事
  1. 背負式の噴霧器で、マンションの駐車場沿いのレッドロビンの生垣に薬剤を散布する作業員

    レッドロビン(ベニカナメモチ)の「ごま色斑点病」対策 東京都杉並区

  2. サクラ 倒木 根鉢 幹の切断面 砧公園

    東京都世田谷区砧公園のサクラ倒木(根返りを伴う倒伏)について 樹木医の考察

  3. デモンストレーション 参加者 ピカス トロニック 機材

    【求人募集】事務スタッフを1名募集します

  4. 剪定鋏 松の枝 松葉 短葉仕立て

    松の伝統技術「短葉仕立て」とは|剪定・芽切り・病害虫管理まで徹底解説

  5. ヒマラヤスギ 根返り 根鉢 駐車場 砧公園

    砧公園で2日連続の倒木事故──ヒマラヤスギはなぜ倒れたのか 樹木医の考察 東京都世田谷区

  6. ベッコウタケ 倒木 樹木医 樹木診断 根 腐朽 腐れ サクラ

    ベッコウタケとは──サクラの根を腐らせるキノコと倒木、見つけたときの診断を樹木医が解説(東京都杉並区の倒木の事例)

  7. 二脚鳥居支柱 添木 杉丸太 杉梢丸太 しゅろ縄 杉皮 樹木支柱 図解

    日本の樹木支柱の種類と歴史──鳥居・八ツ掛・布掛・やぐら、竹と杉丸太としゅろ縄の手仕事|樹木医が解説(Japanese Tree Staking: Torii, Yatsugake and Nunokake)

  8. ヒマラヤスギ 倒木 根鉢 カラーコーン 砧公園

    国土交通省の全国倒木調査を樹木医が読み解く

  9. 樹木医 エアレーション 土壌改良 桜 サクラ 樹勢回復 樹木治療

    サクラ並木 樹木医 土壌改良・エアレーション 東京都

  10. サクラ 幹の根元 樹幹注入 注入器 ウッドスター

    桜の木の毛虫(サクラケムシ)対策──正体はモンクロシャチホコ、毒の有無と発生時期・駆除の方法を樹木医が解説

  1. 玉物 刈り込み 刈込鋏 裏返し 上面 丸み 庭師 図解

    玉物(玉仕立て)の刈込とは──丸い形を保つ庭師の手順と、刈る深さ・時期・小さく戻す方法(Tamamono: How Japanese Gardeners Clip Shrubs into Rounded Forms)

  2. DMM アーボリスト 機材 プーリー ツリークライミング ウェールズ イラスト

    DMM ― ウェールズの鍛造職人たちと Hitch Climber|世界のアーボリスト機材メーカー 第1回

  3. 樹木 点検 時期 落葉期 ケヤキ 双眼鏡 樹木医 管理組合 マンション

    管理組合・施設の樹木の暦──いつ確かめ、いつ頼むか。季節で変わる点検の見どころと、総会から逆算する1年を樹木医が解説

  4. ピカス 解析ソフト 測定点 経路 断面画像 樹木診断 樹木医

    ピカスの解析ソフトでできること──測定点の追加・入り皮の分け読み・強度の見積もり・TreeSA・経年比較

  5. コフキタケ コフキサルノコシカケ 根元 キノコ 樹木医 樹木診断 アーボソニック3D

    コフキタケ(コフキサルノコシカケ)とは──幹を腐らせる多年生のキノコの見分け方と、見つけたときの診断を樹木医が解説

  6. 三又 さんまた 丸太 チェーンブロック 景石 据え付け 造園

    三又(さんまた)の組み方と使い方──丸太と単管パイプで組む方法、開き角・開き止め・脚元と、吊れる重さの考え方を樹木医が解説

  7. アーボソニック3D ピカス 樹種 設定 データベース 樹木医 機器診断

    アーボソニック3Dとピカスで、樹種の設定は結果のどこに効くのか──データベースの値・断面画像の色・日本の樹木の扱いを樹木医が解説

  8. アーボソニック3D ピカス 違い 比較 センサー 釘 音波トモグラフィ 樹木診断 樹木医

    アーボソニック3Dとピカスの違い──同じ音の断面画像でも、最後に出す答えが違う。釘とセンサー、計算、安全率、研究の結果を樹木医が比べる

  9. 育て方 指導者 新人 地上の役 同じ木 樹上作業 アーボリスト イラスト

    一人で樹上の剪定を任されるまで ― 当社の育て方|アーボリストの基礎 第21回

  10. ピカス 歯車効果 断面画像 外周 測定点 年輪 樹木診断 樹木医

    ピカスの歯車効果とは──健全な木でも断面画像の外周に色が出る理由と、見分け方・補正

  1. 癒合剤 切り口 剪定 トップジン へら ブランチカラー 樹木医

    剪定の切り口に癒合剤は必要か──樹木医がトップジン・バッチレートの効果と研究、塗るべき場面をまとめました

関連記事